White Rodgers 1F85RF-275 Installation Guide download pdf (Page 10)

Press Displayed Press or

Step Button(s) (Factory Default) to select Comments

1 System MS2 SS1, HP2, HP1 Selects Single stage, Multi-stage, or Heat Pump

(Single stage or 2-stage) system configuration

2 System LER (OFF) LER (ON) Selects learn mode OFF or ON

3 System OUTSIDE (OFF) OUTSIDE (ON) Selects OUTSIDE sensor OFF or ON

4 System REMOTE (ON) REMOTE (OFF) Selects REMOTE (indoor) sensor OFF or ON

5 System LOCAL (ON) LOCAL (OFF) Selects LOCAL sensor ON or OFF

6 System CH (0) 1 to 9 Select Receiver frequency offset

7 System PRG 4 PRG 0, PRG 2 Selects Programmable Periods

8 System EMR (ON) EMR (OFF) Selects Energy Management Recovery OFF or ON

9 System CR HEAT COOL (FA) SL Selects Fast or Slow cycle selection

10 System CL (OFF) CL (ON) Selects Compressor Lockout CL OFF or ON

11 System CdL (ON) CdL (OFF) Selects Backlight Display ON or OFF

12 System FA HEAT COOL (ON) FA HEAT COOL (OFF) Selects Fast Second Stage ON or OFF

13 System 0 FLTR 0–1950 (increments of 50) Selects filter replacement run time.0 =Disabled

14 System 0 F 4 LO to 4 HI Selects Temperature Display Adjustment 4 LO 4 HI

(Room Temperature)

15 System 4:00 HOLD 0:00 to 8:00 Selects Temporary Program Override Time

(Increments of 15 minutes) 0:00 =Disabled

16 System F C For C selection

Selects temperature display as F° or C°

17 System LR HEAT (90) LR 62 to LR 89 Selects Limited HEAT range

18 System LR COOL (45) LR 46 to LR 82 Selects Limited COOL range

19 System CA (OFF) CA (ON) Selects Comfort Alert Lock

20 System OFF LOCK ON LOCK Selects Button pad Lockout

21 0 00 LOCK 001 to 999 Selects Buttonpad lockout combination number

Press System to set code

Run Returns to the OFF mode

The configuration menu allows you to set certain thermostat

operating characteristics to your system or personal require-

ments.

Set SYSTEM button to OFF, then simultaneously press

and to enter configuration menu. The display will

show the first item in the configuration menu.

The configuration menu table summarizes the configuration

options. An explanation of each option follows.

Press SYSTEM to change to the next menu item. To exit the

menu and return to the program operation, press RUN. If no

keys are pressed within fifteen minutes, the thermostat will

revert to normal operation.

1) Single Stage, Multi-stage or Heat Pump Configuration

This menu item requires you configure the thermostat to

match your system. Choose your system option from the

table below:

System Type Select Option

Single Stage Heat/Cool systems SS1

Multi-Stage Heat/Cool systems (No Heat Pump) MS2

Heat Pump system, 1 compressor or 1 speed compressor HP1

Heat Pump systems, 2 compressors or 2 speed compressor HP2

The thermostat is factory defaulted to MS2. To select a

different option, press the or key to scroll through

the choices.

THERMOSTAT CONFIGURATION MENU

2) Select Learn Mode On or Off – Selecting LER On

enables the learn mode of the thermostat receiver. Your

thermostat is configured at the factory to recognize the

remote sensor shipped with it. The Learn Mode Option

is used only when required as described in Learn Mode

Option.

3) Selects OUTSIDE sensor OFF or ON – Selecting

OUTSIDE ON enables the thermostat to read a wireless

outdoor temperature sensor that has been configured

for Sensor O in the Learn Mode. This allows the thermo-

stat to display the outdoor temperature reading.

4) Selects REMOTE sensor OFF or ON – Selecting

REMOTE ON allows the thermostat to sense an indoor

remote sensor that has been set-up the Learn mode.

The maximum number of Indoor Remote Sensors is 1

configured to sensor A, B or C.

5) Selects LOCAL sensor ON or OFF – Appears if

Remote is set to ON. Selecting LOCAL ON allows the

thermostat to use the onboard temperature sensor

exclusively or for averaging with the remote sensor

readings. To control temperature using only the indoor

remote sensor temperature(s), use the

or buttons

to select LOCAL OFF.

6) Select Receiver frequency offset – Appears if Remote is

set to ON. This option allows you to select a different

channel than the factory default for communication

between the thermostat and remote sensor. Note: If a

INSTALLER/CONFIGURATION MENU

Press the System button until OFF is displayed, then press the and simultaneously

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 19 20

Comments to this Manuals

No comments

White Rodgers 1F85RF-275 Installation Guide Page 10

Comments to this Manuals

Related products and manuals for Remote controls White Rodgers 1F85RF-275