White Rodgers 1F95-0671 Installation Manual download pdf (Page 8)

INSTALLER/CONFIGURATION MENU

5, 6 & 7) Cycle Rate Selection – The factory default setting for

Heat and Cool modes, SS1, MS2, is medium cycle (ME).

For Heat Pump, HP1, HP2, the default setting is medium

(ME). For Emer (Aux) the default setting is fast cycle (FA).

To change cycle rate, press the

or button.

Cycle rate differentials for different settings are:

MODE Fast Medium Slow

FA ME SL

Heat (SS1, MS2) 0.4°F 0.6°F 1.7°F

Cool (SS1, MS2) 0.9°F 1.2°F 1.7°F

Heat Pump (HP1, HP2) 0.9°F 1.2°F 1.7°F

Emer (HP1, HP2) 0.6°F - 1.7°F

8) Select Compressor Lockout CL OFF or ON – Selecting

CL ON will cause the thermostat to wait 5 minutes be-

tween cooling cycles. This is intended to help protect the

compressor from short cycling. Some newer compressors

already have a time delay built in and do not require this

feature. Your compressor manufacturer can tell you if the

lockout feature is already present in their system. When

the thermostat compressor time delay occurs, it will ﬂash

the setpoint for up to ﬁve minutes.

9) System Mode Conﬁguration – This thermostat is conﬁg-

ured for Heat and Cool (SYSTEM switch with Cool Off

Heat) default. It can also be conﬁgured for Heat and Cool

with Auto changeover (Heat, Auto, Cool, Off), Heat only

with fan (Off Heat), Heat only without fan, Auto only

(Auto Off), and Cool only (Cool Off).

10) Select Backlight Display – The display backlight improves

display contrast in low lighting conditions. When the "C"

terminal is powered, selecting backlight CdL ON will keep

the light on continuously. Select backlight OFF will turn the

light on momentarily after any button is pressed. When the

"C" terminal is not powered, the light will be on momentarily

after any button is pressed no matter whether the backlight

is selected ON or OFF.

11) Select Temperature Display Adjustment 4 LO to 4 HI –

Allows you to adjust the room temperature display up to 4°

higher or lower. Your thermostat was accurately calibrated

at the factory, but you have the option to change the dis-

play temperature to match your previous thermostat. The

current or adjusted room temperature will be displayed.

12) Select F° or C° Readout – Changes the display readout

to Celsius or Fahrenheit as required.

13) Select Audio Prompting (Beeper) On or Off – Factory

default setting is on (b, On). To turn off the beeper, select

OFF. Some models do not have a beeper. This setting has

no effect on models without beeper.

14) Program Options: Selects conﬁguration for 7 day (7) or

5/1/1 day (3) programming or non-programming (0) mode.

The default setting is 7, indicating 7 day programming.

The programs per week can be changed to 3 or 0 by

pressing the

or buttons. A selection of 0 days for

non-programmable will eliminate the need for EMR, and

that step in the menu will be skipped.

15) Program Steps per day – This control can be conﬁgured

for 4 or 2 program steps per day. Default is "4 PS" and

can be toggled between 4 PS and 2 PS.

16 & 17) Select Automatic Schedule – With just one touch

of the Auto Schedule key this feature allows you to pro-

gram a desired comfort temperature into all the program

periods along with a 6° set back for night periods of both

Heat and Cool programs. Factory default is "On" for both.

When Heat AS On and Cool AS On are activated while

in Heat or Cool mode, select desired setpoint temperature

and press Auto Schedule. This value will be copied into

all the morning, day and evening program periods. The

night program periods will have a 6°F set back.

18 & 19) Select Fast Second Stage ON or OFF – Heat

pump or Multi-stage only, in the run mode, with the fast

Heat feature enabled (FA Heat On), if the Heat setpoint

temperature is manually raised by 3°F (2°C) or more

above the actual temperature using

the second stage

will energize immediately. With FA OFF, second stage will

not energize until the setpoint temperature is 1°F or more

above actual temperature for more than ten minutes. The

Fast Cool feature (FA Cool) provides the same controls

when the setpoint temperature is lowered.

20) Select Remote Temperature Sensor – This control

allows one wired remote temperature sensor (indoor,

F145-1328, or outdoor, F145-1378) be connected to it and

indicates the measured temperature in clock digits. This

menu enables you to select the remote sensor and also

conﬁgure it as indoor or outdoor temperature sensor. Fac-

tory default is off. Select Remote On and Remote in (for

indoor) or Outdoor Remote.

Local Temperature Sensor disable – This is applicable

only when indoor remote temperature sensor is enabled.

Factory default is Loc On. You can make it Loc Off if you

desire by using

or buttons. Then, only the indoor

remote temperature reading will be used for control

21) Select Daylight Saving Time Calculation – This feature

will allow the thermostat to calculate the DST automati-

cally and apply it to the Real Time Clock display. Default

On. Use or touch keys to select the feature OFF.

22) Keypad Lockout – This step allows you to select the type

of lockout or limited range security required. If no lock-

out or limited range security is required, press MENU to

advance the menu.

Three security settings are available in this menu item.

Use the

or buttons to select the lockout desired.

Lockout selections are:

"Keypad Lockout and L" = Total Lockout. Total Lockout

locks all keys.

"Keypad Lockout and P" = Partial Lockout. Partial Lock-

out allows only the

or buttons to operate within

your set temperature limits.

"Keypad Lockout and Limit" prevents changing the

temperature limits in the Conﬁguration Menu.

Press Menu after selecting the type of lockout.

"Keypad Lockout Combination Number Selection"

Display will read "000" "Keypad Lockout". Note: "000" is

not a valid combination choice.

Skip this step and continue through the remaining conﬁgu-

ration menu items if you require an Air Filter Change out

indicator or Humidiﬁer Pad Change out indicator by press-

ing the MENU button to advance.

Return to this point when you are ready to start your

selected lock-out and continue by:

Press

. Display will read "001".

Pressing

or buttons to select your keypad lock-

out combination number.

Record the number you select for future use.

Press MENU or RunSched to exit the menu. The security

feature you select will start. The system button will remain

active for 10 seconds to allow setting Heat, Off, Cool or

Auto.

23) Limited Heat Range – This feature provides a maximum

setpoint temperature for heat. The default setting is 99°F.

It can be changed between 62°F and 98°F by pressing the

or button.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

White Rodgers 1F95-0671 Installation Manual Page 8

Comments to this Manuals

Related products and manuals for Thermostats White Rodgers 1F95-0671